保得住好有關單層安全玻璃冷凝器，讓其在運用中少發生運行故障，同是讓您也節省了老鼻子較為煩懣。在通常的進行操作運用中，怎麽樣相對更好的投入實際使用有關單層安全玻璃冷凝器，使其充分發揮它的更加最大實際價值。這時候候您就不可沒完沒了解有關單層安全玻璃冷凝器是怎麽樣保得住的？ 1、用前認真進行檢查儀表，安全玻璃瓶有沒有有破碎，各搭接片有沒有相符，進行理會輕拿輕放。
Maintenance of single-layer glass condenser, so that it rarely fails in use, the same allows you to save a lot of trouble. In daily operation and use, how to better apply single-layer glass condenser to make it play its maximum value. At this point, you have to understand how the single-layer glass condenser is maintained? 1. Check the instrument carefully before use. Whether the glass bottle is damaged or not, and whether the interfaces are identical. Take care to handle it lightly. 2、用軟布（能夠使用枕巾紙代替）解放各搭接片，接下來塗抹單薄局部真空脂。（局部真空脂用後準譜兒要蓋好，避免灰砂參加。）
2. Wipe the interfaces with soft cloth (napkins can be used instead) and then apply a little vacuum grease. (Vacuum grease must be well covered to prevent sand from entering.)
3、有關單層安全玻璃冷凝器各搭接片使不得擰得太緊，要進行死期適當活動，防止長時間進行鉤鈐進行引起包括器咬死。
3. The interface of single-layer glass condenser should not be tightened too tightly, so loosen the loosening collar regularly to avoid the long-term locking leading to the connector biting.
4、先開電源供應電門，接下來讓機器由慢到快運行，停工時要使機器正處在需要情況，再關電門。
4. Turn on the power switch first, and then let the machine run from slow to fast. When the machine stops, turn off the switch.
5、處處的聚四氟電門無法過力擰緊，比較容易造成損壞安全玻璃。
5. Polytetrafluoro switches everywhere should not be tightened too tightly, which is easy to damage the glass.
6、老是運用完畢一定要用軟布擦淨加以留在機器要樣兒的多種油跡，汙垢，驅蟲劑剩留，繼續維持保持幹淨。
6. After each use, all kinds of oil marks, stains and solvents left on the surface of the machine must be wiped off with a soft cloth to keep it clean.
7、停工後擰鬆各聚四氟電門，長時間不變在具體工作情況會使聚四氟電子管蛻變。
7. The PTFE piston will be deformed if the PTFE switches are unscrewed after shutdown, and the PTFE piston will be stationary for a long time.
8、進行死期對密封圈開展保持幹淨，辦法是：取下密封圈，進行檢查軸上有沒有積有齷齪，用軟布擦重要，接下來塗單薄局部真空脂，重複裝上相對即可，繼續維持軸與密封圈光滑。
8. Clean the sealing ring regularly by removing the sealing ring, checking whether there is dirt on the shaft, wiping it with a soft cloth, then applying a little vacuum grease and reloading it to keep the shaft and sealing ring smooth.
9、電動一部分切使不得持續進水，加以嚴禁受難。
9. Electrical parts must not be flooded and damp is strictly prohibited.
10、一定要進行采購原廠正宗零配件，隨便采用其餘零配件對機器會導致死亡的破壞。
10. Authentic parts must be purchased from the original factory. The use of other parts at will will will cause fatal damage to the machine.
11、對有關單層安全玻璃冷凝器做任意一種相關情況達到或進行檢查時，準譜兒要先隔離電源供應，汙水源。
11. When repairing or inspecting a single-layer glass condenser, the power supply and water source must be cut off first.
