最近幾年，不鏽鋼冷凝器投入實際使用越來越大範圍，為的是防止顛撲不破影響物品進行澄清到不鏽鋼冷凝器底的狀況出現，其中一種新的不鏽鋼冷凝器應運而生。該產品在戛戛獨造不鏽鋼冷凝器的大體上設計和受到方法的現有基礎上，對不鏽鋼冷凝器底邊做了一部分作出調整。其主要原因在於全部的實際問題都是其主要原因在於顛撲不破影響物品進行澄清到不鏽鋼冷凝器底導致的。這樣的話重點的加以解決解決辦法就是說要迫在眉睫使並未進行配料或進行鼓勵的狀況下也要防止出現進行澄清。這可借助增多其中一個進行顧贍的不鏽鋼冷凝器底而達成，該進行顧贍的不鏽鋼冷凝器底比真實情況的要稍初三點，加以留出3～10公分的暇時。如此顛撲不破影響物將進行澄清在這一進行顧贍的不鏽鋼冷凝器底上，而進行不肯在真實情況的不鏽鋼冷凝器底上逐漸形成絕熱層。 In recent years, stainlesssteel reactor（www.gfanyingfu.com） is applied more and more widely, in order to avoid solid reactantprecipitation to stainless steel reaction kettle, a new stainless steel reactoremerges with the tide of the times. The products in the original stainlesssteel reactor design and heating method based, so the bottom of the reactionkettle do some adjustments.Because all of the problemsare due to solid reaction material to the stainless steel reaction kettlebottom caused by precipitation. So the main solution is to avoid precipitationeven if there is no mixing or stirring. It by adding an auxiliary stainlesssteel reaction kettle bottom and the realization and the auxiliary stainlesssteel reaction kettle bottom than the actual to slightly higher, leaving 3 ~ 10cm gap. This solid reactant will be deposited in the auxiliary stainless steelreaction kettle without actual stainless steel reaction kettle bottom formationheat insulating layer.
借助不鏽鋼冷凝器底暇時間的對流實際作用熱進行通報將是接連不斷平均的。 進行顧贍的不鏽鋼冷凝器底用高極限抗拉強度不鏽鋼(SS314)釀成，方麵包括很多有關小孔，孔徑比影響物品的粒徑略小，將這一類型的情況篩網切成圓圈。其邊際進行絨毛躬身行禮作昂首闊步，當顛撲不破影響物品載荷很重時，進行顧贍下麵麵能夠加其中一個非金屬環進行進行進行支撐。如此便可防止顛撲不破物品進行齊集在不鏽鋼冷凝器底。
Through the convection heattransfer between the stainless steel reactor bottom gap will be continuous anduniform. Auxiliary stainless steel reaction kettle is made of high strengthstainless steel (SS314) and above with a plurality of small holes, apertureratio of reactants particle size smaller, will this kind of screen intocircular. The edge is bent down as a support, and when the solid reactionmaterial load is heavy, the auxiliary bottom can be added with a metal ring asa support. This is to avoid the solid material in stainless steel reactionkettle.
